Kit aereo Sopwith Triplane in scala 1/48 - Modello Eduard.Contenuto della confezionePlastic sprue, Fotoincisioni, Resin (cast), Metallo bianco, Film fotografico, Foglio di decals (applicabile con acqua)
Kit aereo Sopwith Triplane Flying Circus Edition in scala 1/48 - Modello Eduard.Il kit è il Sopwith Triplane (8014) di Eduard. Si tratta di uno dei primi modelli in scala 1/48 di Eduard, risalente al 1995, ed è stato il primo kit Eduard a non essere un prodotto a tiratura limitata. È un kit a tecnica mista ed è composto da plastica stampata a iniezione, un grande fret inciso, un motore in metallo bianco e il primo stabilizzatore orizzontale, simile a quello utilizzato dal Sopwith Pup.Il Kit contiene parti in plastica e fotoincisioni in metallo per un modello, foglio decalcomanie e instruzioni dettagliate.
Kit aereo Morane-Saulnier Type L in scala 1/48 - Modello Eduard.Contenuto della confezionePlastic sprue (Light gray), Fotoincisioni (Brass), Film fotografico (Clear), Foglio di decals (applicabile con acqua) (Multi-color), Metallo
Kit aereo Fokker E.III in scala 1/48 - Modello Eduard.Edizione originale Eduard del caccia tedesco della Prima Guerra Mondiale, il Fokker E.III Eindecker. Il kit è ben stampato e include fotoincisione e motore in metallo bianco
Kit aereo DFW-28 Floh Never Fighting Ladies Edition in scala 1/48 - Modello Eduard.Edizione originale Eduard del 1995 di un prototipo della Prima Guerra Mondiale, il DFW-28 Floh "Flea".Progettato come biplano da caccia monoposto leggero, raggiungeva una velocità massima di 180 km/h. Tuttavia, l'esercito rinunciò allo sviluppo di questa "pulce da combattimento". Il kit include fotoincisione, pellicola per il pannello strumenti e abitacolo ben dettagliato.
Sopwith Baby 1/72 Scale Airplane Kit - Eduard Model. This is a rare 1/72 scale, limited edition classic kit with injection molded plastic parts and etched brass parts. It is probably the only injection molded plastic kit of this early British WWI seaplane.
Albatros C.III fighter plane kit in 1/48 scale - Eduard Model. Eduard has produced a detailed scale model of the iconic World War I two-seater aircraft, the Albatros C.III. This kit includes resin parts, photoetch (interior) and cast metal (engine) for additional detail. A beautiful kit, which assembles into a striking model. Markings include two a/c Luftstreitkrafte, one of which was flown by Lt. Bohme / Lademacher.
Vickers Wellington main wheels and tail wheel with 1/72 scale leg for Special Hobby kit - CMK detail set.For the reissue of the Special Hobby Wellington model, new and more detailed resin main wheels and tail wheel have been prepared. The real paw is 3D printed using a special stronger material.
SABELT 6-POINT BLACK 1/24 scale seat belts - HGW Models.The belts are made of genuine micro-fiber and, in combination with the included photoetched buckles, offer an extremely realistic appearance.ancillary featurescontains micro-fabric and highly detailed photoetched partsthe belts are fully functional: the modeler can leave them unfastened/fastenedmade of printed micro-fabric material that behaves like a ragthe textile parts are prepared for the use of filters and other agents (they are waterproof and resistant to common non-aggressive modeling preparationsINSTRUCTIONSRemove the pre-cut textile part from the sheet.Remove the backing paper.Gather the belts and knead them between your fingers.Thread the belts into the photo-etched buckles, using superglue.Place them on the seat.Spray with gloss paint.Spray with matte paint.Impregnate the belts with a very dilute oil color (mix of black and brown) > highlight the texture.
Embossed print Stitching World War I in 1/72 scale - HGW Models.No protective film! Just dip the seat belts in water, peel them off the paper and place them where you need them.Instructions:1. Place it in a drop of water for about 1 minute.2. Take the part with sharp tweezers3. and place it in the appropriate spot on the model.
1/48 scale P-40E Warhawk seat belts - HGW Models.Special technology allows seat belts to be printed in the appropriate size and thickness and transferred without the backing film. Simply dip the belts in water, peel them off the paper and place them on the driver's seat.Instructions:1. Place it in a drop of water for about 1 minute.2. Take the part with sharp tweezers3. and place it in the appropriate spot on the model.
P-40 1/48 scale seat belts - HGW Models.Harnesses designed for the P-40i in 1/48 scale . The belts are made of micro-fiber and, in combination with the included photoetched buckles, offer an extremely realistic appearance.ancillary featurescontains micro-fabric and highly detailed photo-etched partsbelts are fully functional: the modeler can leave them unfastened/fastenedmade of molded micro-fabric material that behaves like a ragtextile parts are prepared for use with filters and other agents (they are waterproof and resistant to common non-aggressive modeling preparationsINSTRUCTIONSRemove the pre-cut textile part from the sheet.Remove the backing paper.Gather the belts and knead them between your fingers.Thread the belts into the photo-etched buckles, using superglue.Place them on the seat.Spray with gloss paint.Spray with matte paint.Impregnate the belts with a very dilute oil color (mix of black and brown) > highlight the texture.
Messerschmitt Bf 109F/G seat belts in 1/72 scale - HGW Models.Special technology allows seat belts to be printed in the appropriate size and thickness and transferred without the backing film. Simply dip the belts in water, peel them off the paper and place them on the driver's seat.Instructions:1. Place it in a drop of water for about 1 minute.2. Take the part with sharp tweezers3. and place it in the appropriate spot on the model.
Messerschmitt Bf 109E seat belts in 1/72 scale - HGW Models.Special technology allows seat belts to be printed in the appropriate size and thickness and transferred without the backing film. Simply dip the belts in water, peel them off the paper and place them on the driver's seat.Instructions:1. Place it in a drop of water for about 1 minute.2. Take the part with sharp tweezers3. and place it in the appropriate spot on the model.